Posts
best baby monitor dual receiver image
rynearson9
I get decent signal on the main floor and when i go in the basement my signal sucks. I have Verizon
Answer
Well here is some information that tells you what interferes with wireless signal:
Sources of interference for wireless devices and networks
The farther away the interference source, the less likely it is to cause an issue. The following items can cause interference with wireless communication:
* Microwave ovens: Placing your computer, Bluetooth wireless device, or AirPort base station near a microwave oven that is in use may cause interference.
* Direct Satellite Service (DSS) RF leakage: The coax cable that comes with certain types of satellite dishes may cause interference. Obtain newer cables if you suspect RF leakage.
* Certain electrical devices such as power lines, electrical railroad tracks, and power stations.
* 2.4 GHz or 5 GHz phones: A cordless telephone that operates in this range may cause interference with wireless devices or networks when used.
* Metal objects: If possible, move metal objects or change the placement of the computer, wireless device or wireless access point so the path between your computer and the wireless device or wireless access point is free from metal objects that may cause interference.
* Video senders (transmitters/receivers) that operate in the 2.4 GHz or 5 GHz bandwidth.
* Wireless speakers that operate in the 2.4 GHz or 5 GHz bandwidth.
* Certain external monitors and LCD displays: Certain displays may emit harmonic interference, especially in the 2.4GHz bandwidth between channels 11 and 14. This interference may be at its worst if you have a portable computer with the lid closed and an external monitor connected to it. Try changing your access point to use 5 Ghz or a lower 2.4 GHz channel.
* Any other "wireless" devices that operate in the 2.4 GHz or 5 GHz bandwidth (microwaves, cameras, baby monitors, and so on).
Note: Some devices may not overtly state that they operate in the 2.4 GHz or 5 GHz bandwidth. The operations manual should indicate the frequencies the device uses to operate. These may be referred to as "Dual Band" or "Wireless" devices.
Effect of home and office elements on wireless communication
Where you are located and what materials you are surrounded by can affect your wireless networking performance or Bluetooth wireless device. The table below shows common elements and their potential for interference.
Type of Barrier Interference Potential
Wood Low Interference
Plaster Low Interference
Synthetic material Low Interference
Glass Low Interference
Water Medium Interference
Bricks Medium Interference
Marble Medium Interference
Paper rolls High Interference
Concrete High Interference
Bulletproof glass High Interference
Metal Very high Interference
I would say your problem is Concrete because of the bricks, which are almost the hardest next to metal and bulletproof glass... But if you can get a wireless access point and get it at the entrance of the basement, it will take the signal from your router and extend it into your basement. You can take these WAPoints and move them around to see where you get the best signal in your basement with where the access point extends the signal too. I hope this helps. Also some of the other items listed above can cause inteference but I would suspect the concrete and start there. There not too expensive and you can have more than one.
Well here is some information that tells you what interferes with wireless signal:
Sources of interference for wireless devices and networks
The farther away the interference source, the less likely it is to cause an issue. The following items can cause interference with wireless communication:
* Microwave ovens: Placing your computer, Bluetooth wireless device, or AirPort base station near a microwave oven that is in use may cause interference.
* Direct Satellite Service (DSS) RF leakage: The coax cable that comes with certain types of satellite dishes may cause interference. Obtain newer cables if you suspect RF leakage.
* Certain electrical devices such as power lines, electrical railroad tracks, and power stations.
* 2.4 GHz or 5 GHz phones: A cordless telephone that operates in this range may cause interference with wireless devices or networks when used.
* Metal objects: If possible, move metal objects or change the placement of the computer, wireless device or wireless access point so the path between your computer and the wireless device or wireless access point is free from metal objects that may cause interference.
* Video senders (transmitters/receivers) that operate in the 2.4 GHz or 5 GHz bandwidth.
* Wireless speakers that operate in the 2.4 GHz or 5 GHz bandwidth.
* Certain external monitors and LCD displays: Certain displays may emit harmonic interference, especially in the 2.4GHz bandwidth between channels 11 and 14. This interference may be at its worst if you have a portable computer with the lid closed and an external monitor connected to it. Try changing your access point to use 5 Ghz or a lower 2.4 GHz channel.
* Any other "wireless" devices that operate in the 2.4 GHz or 5 GHz bandwidth (microwaves, cameras, baby monitors, and so on).
Note: Some devices may not overtly state that they operate in the 2.4 GHz or 5 GHz bandwidth. The operations manual should indicate the frequencies the device uses to operate. These may be referred to as "Dual Band" or "Wireless" devices.
Effect of home and office elements on wireless communication
Where you are located and what materials you are surrounded by can affect your wireless networking performance or Bluetooth wireless device. The table below shows common elements and their potential for interference.
Type of Barrier Interference Potential
Wood Low Interference
Plaster Low Interference
Synthetic material Low Interference
Glass Low Interference
Water Medium Interference
Bricks Medium Interference
Marble Medium Interference
Paper rolls High Interference
Concrete High Interference
Bulletproof glass High Interference
Metal Very high Interference
I would say your problem is Concrete because of the bricks, which are almost the hardest next to metal and bulletproof glass... But if you can get a wireless access point and get it at the entrance of the basement, it will take the signal from your router and extend it into your basement. You can take these WAPoints and move them around to see where you get the best signal in your basement with where the access point extends the signal too. I hope this helps. Also some of the other items listed above can cause inteference but I would suspect the concrete and start there. There not too expensive and you can have more than one.
Upgrading router, what is a great one to buy?
~~ Pola
I will spend up to $150 and no more for a router. The router we have currently gives out great signal but with all the new technologies that have come out, it fusses if we add multiple devices to it so it is time to upgrade! Currently I have a Netgear router (bought it 5 years ago). Thanks for the help!
Dr.Dave - One example) Whenever we tried Facetime via iPhones, the connection would be there for 30 seconds then completely cut off.
Answer
Most any router can handle 20+ devices.
My Netgear WNDR4000 currently has 25 connections, 8 via Ethernet and 17 via WiFi with no problems whatsoever. The WNDR4000 is not sold anymore, but here is a slightly newer model. http://www.amazon.com/gp/product/B008HO9DK4/ref=as_li_ss_tl?ie=UTF8&camp=1789&creative=390957&creativeASIN=B008HO9DK4&linkCode=as2&tag=excharge-20
You would likely be better off to upgrade your Internet connection.
Here is how it works,
A wireless router connects two separate networks. In your case it would connect the Internet connection from your ISP with your local home network (LAN).
Internet speed is measured in Mbps and determined by the ISP plan that you purchase. You can measure your Internet speed here: http://speedtest.net
No router or connection type will change your Internet speed. This connection bandwidth is shared by your entire LAN via your router. So any bandwidth others are using will be deducted from the total Internet speed that is available to you. In simple terms, the more users you have the more speed will be required. Things such as streaming video (Netflix) suck up a lot of bandwidth. Here are Netflix minimum speed recommendations. https://support.netflix.com/en/node/306
For example if you have a 3 Mbps Internet connection and one user is utilizing 2.5 Mbps of the bandwidth to stream a Netflix movie that only leaves 0.5 Mbps for all of the rest of the users on the LAN.
The only real way to speed up your Internet connection is to get a faster ISP or speed tier.
As long as the connected devices are not actively using the Internet connection they do not consume bandwidth or slow the connection down.
Many people would be likely be surprised at how many active connections their wireless router has. I have dozens. Cell phones, tablets, iPods, game consoles, laptops, desktops, ROKU boxes, Internet enabled devices such as TVs and audio receivers, and the list goes on.
That being said,
Wireless signals are affected by many factors including wall density, electrical interference, directional antenna range, etc. 2.4 GHz WiFi connections also experience interference from microwave ovens and cordless phones which interfere with the 2.4 GHz band.
Dual band routers have multiple wireless radios enabling broadcast on the 2.4 GHz and 5 GHz bands simultaneously. Using the 5 GHz band cuts down on interference from cordless phones and microwave ovens.. Not
Most any router can handle 20+ devices.
My Netgear WNDR4000 currently has 25 connections, 8 via Ethernet and 17 via WiFi with no problems whatsoever. The WNDR4000 is not sold anymore, but here is a slightly newer model. http://www.amazon.com/gp/product/B008HO9DK4/ref=as_li_ss_tl?ie=UTF8&camp=1789&creative=390957&creativeASIN=B008HO9DK4&linkCode=as2&tag=excharge-20
You would likely be better off to upgrade your Internet connection.
Here is how it works,
A wireless router connects two separate networks. In your case it would connect the Internet connection from your ISP with your local home network (LAN).
Internet speed is measured in Mbps and determined by the ISP plan that you purchase. You can measure your Internet speed here: http://speedtest.net
No router or connection type will change your Internet speed. This connection bandwidth is shared by your entire LAN via your router. So any bandwidth others are using will be deducted from the total Internet speed that is available to you. In simple terms, the more users you have the more speed will be required. Things such as streaming video (Netflix) suck up a lot of bandwidth. Here are Netflix minimum speed recommendations. https://support.netflix.com/en/node/306
For example if you have a 3 Mbps Internet connection and one user is utilizing 2.5 Mbps of the bandwidth to stream a Netflix movie that only leaves 0.5 Mbps for all of the rest of the users on the LAN.
The only real way to speed up your Internet connection is to get a faster ISP or speed tier.
As long as the connected devices are not actively using the Internet connection they do not consume bandwidth or slow the connection down.
Many people would be likely be surprised at how many active connections their wireless router has. I have dozens. Cell phones, tablets, iPods, game consoles, laptops, desktops, ROKU boxes, Internet enabled devices such as TVs and audio receivers, and the list goes on.
That being said,
Wireless signals are affected by many factors including wall density, electrical interference, directional antenna range, etc. 2.4 GHz WiFi connections also experience interference from microwave ovens and cordless phones which interfere with the 2.4 GHz band.
Dual band routers have multiple wireless radios enabling broadcast on the 2.4 GHz and 5 GHz bands simultaneously. Using the 5 GHz band cuts down on interference from cordless phones and microwave ovens.. Not
No comments:
Post a Comment